HDPE Large Radius Sweep Bend
For layouts that need a smoother change of direction, Smart Joint supplies hdpe sweep bends with a seamless HDPE body and a large radius of curvature, and as an experienced hdpe sweep bend manufacturer we support project-specific angle cuts, SDR7 or SDR9 wall options, and diameters from 90 mm up to 1600 mm.
Seamless Construction for Demanding Piping Layouts
This HDPE sweep bend is built with a large radius of curvature so the direction change happens more gradually. The seamless body has no welded seams and keeps a uniform wall thickness, which supports a smooth finish and a clean appearance.
Large Radius of Curvature
The design allows a smoother and more gradual change in direction than a short-radius layout.
Seamless HDPE Body
The bend is made from high-density polyethylene with no welded seams and uniform wall thickness.
Lower Friction
A lower coefficient of friction than other types of bends helps reduce pressure drop and pumping energy.
Fixed Shape
The shape is fixed and does not bounce back, unlike pipe-bent and fabricated bends.
Specifications at a Glance
Use the table below to match the bend to your project requirements. The page lists the size range, wall thickness variants, radius options, construction, and customization details for this product.
| Material | High-density polyethylene (HDPE) |
|---|---|
| Size range | 90 mm up to 1600 mm diameter |
| Wall thickness variants | SDR7 and SDR9 |
| Radius / curvature | 90 mm–355 mm in 3D; 400 mm–1600 mm in 2D, with a smaller radius noted as lower cost |
| Construction | Seamless, no welded seams, uniform wall thickness |
| Customization | Angle cuts customized per project requirement |
Choosing Radius and Wall Thickness
Start with the available space and the required direction change. The page separates 90–355 mm into 3D bends and 400–1600 mm into 2D bends, and it notes that a smaller radius is lower cost. Wall thickness is available in SDR7 and SDR9; the page notes that these thicker wall options are difficult to achieve with pipe bending.
If the layout calls for a non-standard angle, the angle can be cut to project requirements. For 3D sweep bends from 90 mm to 355 mm, the page encourages butt welding with a flange stub on site or at the workshop.
3D Sweep Bends
Listed for 90 mm–355 mm, with butt welding to a flange stub encouraged on site or at the workshop.
2D Sweep Bends
Listed for 400 mm–1600 mm, with a note that a smaller radius is lower cost.
SDR7 and SDR9
Two wall thickness variants are offered, including thick-wall options that are difficult to achieve by pipe bending.
Custom Angle Cuts
The bend angle can be cut per requirement, so it can be matched to project specifications.
Where a Large Radius Bend Fits
A smoother, more gradual turn helps reduce pressure drop when fluid flows through the line. The product page lists mining, water, gas, and industrial piping projects as suitable applications. In these systems, the seamless HDPE construction and uniform wall thickness support a clean internal profile, while the lower coefficient of friction supports more efficient flow and reduced pumping energy.
Mining Piping
For mining piping projects where a gradual direction change and seamless HDPE construction are required.
Water Piping
For water piping layouts that benefit from a smooth, large-radius bend and uniform wall thickness.
Gas Piping
For gas piping projects that call for an HDPE sweep bend with a fixed shape and no welded seams.
Industrial Piping
For industrial piping systems where lower friction and reduced pressure drop support efficient flow.
Seamless HDPE Performance
The seamless construction has no welded seams and maintains uniform wall thickness at any point. The page states 100% no pressure derating for this product. The bend has a lower coefficient of friction than other types of bends, which helps reduce pressure drop and improve piping system efficiency. The page also notes a better appearance and smooth finish.
The shape remains fixed without bounce back, so the bend holds its intended geometry. This contrasts with pipe-bent and fabricated bends. The result is a clean, smooth HDPE sweep bend that is designed for consistent flow and a more gradual change in direction.
No Welded Seams
The body is seamless, with no welded seams along the bend.
Uniform Wall Thickness
Wall thickness remains uniform at any point, with 100% no pressure derating stated.
Lower Pressure Drop
The lower coefficient of friction helps reduce pressure drop and pumping energy.
No Bounce Back
The shape is fixed and does not bounce back after forming.
Before You Place an Order
Confirm the diameter, wall thickness, radius type, angle, and connection details against the project drawing. For 3D sweep bends from 90 mm to 355 mm, the page encourages butt welding with a flange stub on site or at the workshop.
Company information on the product page states manufacturing since 1992, about 30 years of experience, ISO certification, and watermark, WRAS, and NSF certificates at company level. Ask for the current documents that apply to your project.
Diameter
Select from 90 mm up to 1600 mm.
Wall Thickness
Choose SDR7 or SDR9 for the project requirement.
Radius Type
3D is listed for 90–355 mm; 2D is listed for 400–1600 mm.
Angle and Connection
Confirm the custom angle and the planned flange stub connection before ordering.
Discuss Your HDPE Sweep Bend Requirements
Send the diameter, SDR, radius type, angle, and connection details for a project review. The product is inquiry-based, so contact the team to confirm options and documentation.
Frequently Asked Questions
what size range and wall thicknesses are available for this hdpe sweep bend?
the product is available in diameters from 90 mm up to 1600 mm. wall thickness variants are sdr7 and sdr9. the page notes that thick-wall options such as these are difficult to achieve with pipe bending.
what is the difference between the 2d and 3d radius options?
the page lists 90 mm–355 mm for 3d sweep bends and 400 mm–1600 mm for 2d sweep bends. it also notes that a smaller radius is lower cost. the choice should follow the available space, required direction change, and project layout.
is the hdpe sweep bend seamless?
yes. the bend has a seamless construction with no welded seams. it is made from high-density polyethylene and maintains uniform wall thickness at any point, with 100% no pressure derating stated for the product.
can the bend angle be customized?
yes. the angle can be cut per requirement, so angles can be customized to project specifications. provide the required angle and connection details when requesting a project review.
which applications is the sweep bend suitable for?
the product page lists mining, water, gas, and industrial piping projects. its large radius supports a smoother, more gradual change in direction, and the lower coefficient of friction helps reduce pressure drop when fluid flows through the line.
how are 3d sweep bends from 90 mm to 355 mm connected?
for 3d sweep bends from 90 mm to 355 mm, the page encourages butt welding with a flange stub on site or at the workshop. confirm the connection method and flange details against the project drawing before ordering.









